cordless tools kit

Combination Household Tools Bag is applicable to family use. You can take it wherever you go.

1.For timing the chain on 1.0/1.2/1.4 EcoTec twin cam engines.
2.Applications for Corsa, Agila, Astra, Tigra and Meriva.

1.Suitable For VW T5 As Of 2004, TOUAREG & Phaeton As Of 2003 With 5 & 10 Cylinder Engines.
2.Camshaft Locking Tools,Camshaft Gear Retaining Tool.

Includes:bit,socket ,adapter,pliers,extension bar,bit holder,hex key

Suitable for VAG 1.6 and 2.0 TDI .Designed to fit the newest Common Rail diesel engines which are significantly different from the older PD engines

standard tool kit makes your work more professional and more easy. it comes with different sizes of socket and screwdriver bits, pliers, wrenches, etc

Suitable for timing 1.4 & 1.6 Valvetronic direct injection petrol, chain drive engines, fitted in BMW Mini, Citroen and Peugeot vehicles.

Includes;gloves,scissors,utility knife,tape measure,claw hammer

1.Suitable For VW T5 As Of 2004, TOUAREG & Phaeton As Of 2003 With 5 & 10 Cylinder Engines.
2.Camshaft Locking Tools,Camshaft Gear Retaining Tool.

To name a few, the kit includes a wire brush,metric hex keys,ratcheting bit driver, slotted precision screwdriver, etc.

1. Camshaft setting and flywheel locking tools.
2. For BMW M47/TU/T2 and M57/TU/T2 diesel engines, Land Rover, Rover/MG and Vauxhall/Opel model.

1.Designed for push back and wind back brake pistons.
2.Adaptor set applicable for wide variety of vehicles.
3.16 adapters and 8 pcs brake tools.

1.Built-in bearing makes balancer replacing job easy.
2.6-slot puller plate plus 9 threaded adapters fit to balancers on most cars.

Suitable for single, twin and quad camshaft
1.Camshaft Locking Pins(2)
2.Flywheel Plate Locking Tool
3.Flywheel Locking Tool with Bolts M6x90mm

1. for removal of seized Injectors on Citroen and Peugeot diesel HDi engines.
2. Removal injectors without removing the cylinde.

Suitable for removing the water pump on
Pumpe Duse, diesel, gear drive engines.
Essential to align the engine in the TDC
position.

1.For easily alignment of clutch disc and flywheel.
2.Suitable for most vehicles such as VW, BMW, Ford, Vauxhall, Renault.

1.For Volkswagen Audi Group (VAG) 1.4 and 1.6 FSi Petrol engines.
2.Contains crank TDC positioning, camshaft setting and tensioner lock tools.

1. Remove/Install rear sub-frame bushes in Mondeo.
2. No need to remove sub-frame from vehicle.
3.Applications for Ford Mondeo 2001, 10/2000 onwards

For removing and replacing rear and upper and lower bushes (rose bushes) on trailing arm suspensions and 2 rear anti roll bar bushes.

1.25, 1.4, 1.6, 2.0, 2.3, 1.6 v16, 2.0 RS, 1.6 Ti-VRC, 1.8 SCi, 2.0 ST 150, 2.0 XHR petrol, 1.8 TDdi, 1.8 TD, 1.8, 2.2, 2.2 TDCI engines. 1.6 Ti-VCT

1.Aluminum anodized cylinder and aluminum cylinder head.
2. To be widely used in auto repair,leak tests,experiments,vacuum packaging and so on.

1.Dual tie rod tool and 3 adapters.
2.1/2" drive ratchet.
3.For use on most Chrysler, Ford and GM vehicles.
4.Without removing steering gear.

1.For 2.5 / 2.8 CRD timing belt engines, Chrysler, Jeep and LDV.
2.Contains camshaft, crankshaft and balance shaft pins, plus tensioner adjuster.

Petrol Engine Setting/Locking Tool Kit for BMW engines 2.5 and 3.0 with Valvetronic (N51, N52, N52K, N55) or Direct Injection (N53, N54.)

1.Designed to remove wires from terminals without damage.
2.Also designed for Pack-Con and Weather-Pack terminals found on many GM vehicles.

Engine Timing Tool Kit for BMW 1, 3 and 5 Series with chain driven engines. Check, adjust and set the Camshaft timing and remove the Cam chain.

1.For VW Audi VAG 1.4tdi, 1.9 tdi pd.
2.3 double pin wrenches,90 degree pin,Triangular pin,Circle pin.
3.Dipped foam handles
4.Mirror polished pins

1. To remove and install press-fit control arm ball joints on BMW 3 series cars.
2. Ball joints can be quickly removed and installed.

designed for pulling off the camshaft timing belt wheel and locking or postioning the engine output shafts,such as the camshaft and crankshaft.